DED9

What Are The Components Of Local Area Networks?

Local Area Networks (LANs) Are One Of The Most Stable Communication Mechanisms That Use Different Layers Such As Data And Physical To Transmit Information.

In communications, the networks that cover a limited area are called the Local Area Network (LAN), and the networks that cover a wide area are called the Wide Area Network (WAN). LANs are generally divided into two main groups: wired LANs and wireless LANs. Over the past two decades, various wired and wireless communication technologies have been introduced to the world of technology, and only a few have received attention.

The critical thing to note is that LANs will not be left out of the tech world. Unfortunately, some network experts have been urging companies to use wireless LANs to reduce implementation costs now, as these networks perform better than wired models.

The point to keep in mind is that wired LANs will not go away, or at least not in the short term, because wired LANs’ stability, performance, and security are not comparable to wireless networks.

Therefore, it is better to check the requirements of your business before making a final decision and then choose the correct option.

Cable local area network (Ethernet)

A local area network is a computer network designed for a limited geographic area, such as a building or campus. Although a LAN can be implemented as an isolated network to connect an organization’s computers and access shared resources, on a large scale today, most LANs connect to a WAN or the Internet.

The 1980s and 1990s developed various communication standards and protocols for wired LANs, each with advantages and disadvantages. At the same time, the IEEE proposed that the data link layer be divided into Logical link control (LLC) subtitles and Medium Access Control (MAC) subtitles. Data (DLC) is called Data-Link Layer.

The institute developed several physical layer standards for various LAN protocols to simplify the management of local area networks and improve their performance. In general, all LANs Wires use a media access control (MAC) mechanism that provides a secure way for nodes in a network to interact with each other. Figure 1 shows how the IEEE 802 standard interacts with the TCP / IP protocol suite.

Ethernet was developed in the 1970s by Robert Metcalfe and David Boggs. Since then, four generations of this standard have been created: standard Ethernet (10 Mbps), fast Ethernet (100 Mbps), Gigabit Ethernet (1 Gbps), and 10 Gigabit Ethernet (10 Gbps) ) are. And figure 2 shows the generation trend of different generations. Almost all innovative technologies for wired networks other than Ethernet have disappeared from the market, as Ethernet has been able to keep up with the changing world of technology.

figure 1

figure 2

Standard Ethernet (10 Mbps)

We call introductory Ethernet data rates of 10 Mbps. Standard Ethernet is the mother of all modern standards. Some features of this standard have changed or become obsolete over time, but some of the standard Ethernet features have not changed over the years and have been incorporated into other means. The unchanged features are as follows:

Offline and unreliable service

(Connectionless and Unreliable Service)

Ethernet provides offline service, meaning that each frame sent is independent of the previous or next structure. Ethernet does not define any mechanism for starting or ending a connection. The sender sends whenever he has a frame, in which case the receiver may be ready to receive or may not be prepared to do so. This approach has a significant drawback, as the transmitter may send frames to the receiver consecutively, which reduces network performance. Here, if a structure is lost, the sender’s data link layer will not notice unless an upstream protocol (upper layer) monitors the sending process. If a frame breaks during transmission and the receiver sees it, it will do nothing, as the upstream protocols must investigate and address the issue. So we have to say that Ethernet is not reliable by itself.

Frame Format

The Ethernet frame consists of seven fields designed to do a specific job (Figure 3). The description of each of these fields is as follows:

Figure 3

Frame size

Ethernet sets limits on the minimum and maximum size of a frame. For example, if the Ethernet network uses the CSMA / CD access method to send packets, a minimum length limit must be set so that packages can be transmitted smoothly. An Ethernet frame must be at least 64 bytes. Part of this site is related to the title and sequence.

If we count 18 bytes of the header and sequence (6 bytes of source address, 6 bytes of destination address, 2 bytes of length or type, and 4 bytes of CRC) and subtract the above value from 64, we get 46, which is the minimum length of the upstream layer. If the upstream layer package is less than 46 bytes, we must use the mentioned padding technique to compensate for the difference.

The Ethernet standard defines a maximum length of one frame (without preamble and SFD field) as 1518 bytes. If we subtract 18 bytes and reduce the sequence, the entire packet length is 1500 bytes.

Addressing

Each station on an Ethernet network (such as PCs, workstations, or printers) has its network interface card (NIC). The workstation network card specifies the address of the workstation link layer. This Ethernet address is 6 bytes written on a hexadecimal basis, and two dots separate its bytes. For example, an Ethernet URL could be written as follows:

47: 20: 1B: 2E: 08: EE

Transfer address bits

How to send addresses in the real world is different from how to write them in hexadecimal format. Here, the transition from left to right and byte is done. However, the least valuable bit (the rightmost bit) is sent first, and the last helpful bit is sent for each byte. A bit that defines an address as unicast or multicast is first delivered to the recipient.

The above approach helps the receiver determine if it receives a single-player or multi-player package. To clarify the discussion, pay attention to the following example. In Figure 4, you can see how the address 47: 20: 1B: 2E: 08: EE is sent.

Figure 4

Unicast, Multicast, and Broadcast addresses

The source address is always a unicast address, meaning that the frame only comes from one station. However, the destination address can be single-broadcast, multicast, or broadcast. If the low byte bit of the first byte in the destination address is 0, it is a single-bit address. Otherwise, it is multicast. A multicast address is a particular type of multicast address that indicates the packet receivers of all LAN stations.

A destination broadcast address contains 48 1s (equivalent to F in a hexadecimal system). We need to give a practical example to learn more about these three addresses. In the following example, we want to identify the following type of destination addresses:

4A: 30: 10: 21: 10: 1A

47: 20: 1B: 2E: 08: EE

FF: FF: FF: FF: FF: FF

To identify the address type, we must look at the second hexadecimal digit from the left. The address is a single-player if it is even (the least valuable bit is 0). If it is an individual (the least valuable bit is 1), it is a multicast address. And if all digits are F, the address is ubiquitous. So we have the following:

Implementation

Standard Ethernet can implement in various ways, but only four are famous. The following table summarizes the implementation of standard Ethernet.

In the 10BaseX naming system, the number that replaces the X determines the data rate. The word Base means digital (base) signal, and X indicates approximately the maximum cable size or cable type. Standard Ethernet uses a baseband signal; This means that the bits are converted to a digital signal and sent directly over the line.

Fast Ethernet (100 Mbps)

In the 1990s, some LAN technologies with a transfer rate of more than 10 Mbps emerged, such as Fiber Distributed Data Interface (FDDI) and Fiber Channel. Ethernet made a giant leap by increasing the transfer rate to 100 Mbps, so I used Fast Ethernet to describe it. Of course, fast Ethernet designers had to adopt new technology to standard Ethernet; Hence the Mac sublayer remained unchanged.

It means that the frame format, maximum and minimum size remained unchanged. As the transmission rate increased, standard Ethernet features that depended on transmission rate, access method, and implementation were revised. The goals of high-speed Ethernet can be summarized as follows:

Access method

Good CSMA / CD performance depends on transfer rate, minimum frame size, and maximum network length. The ultimate network length must change if we want to keep the minimum frame size. In other words, if the minimum frame size is still 512 bits and packets are sent ten times faster, the collision should be detected ten times earlier, meaning that the maximum network length should be ten times shorter (propagation speed unchanged). Therefore, I developed two solutions in interaction with fast Ethernet.

The first solution was to completely abandon the bus topology and use a passive, star-shaped topology but increase the maximum network size to 250 meters instead of the standard 2,500 meters as standard Ethernet.

This approach was proposed for standard Ethernet compatibility.

The link-layer controller receives a frame from the source host and stores it in a buffer (queue) awaiting processing. The second solution is to use a buffer switch to store the shelves and connect the duplex to each host so that the transmission media has a private function for each host. CSMA / CD is not required in this case, as the hosts do not compete with each other to send packets.

It then checks the destination address and sends the frame from the appropriate interface. Since the connection to the switch is full-duplex, the destination address can even send a frame to another station simultaneously as receiving the frame.

Auto-negotiation

The above part offers a wide range of features to a station or a hub. A new feature added to Fast Ethernet is called Auto-negotiation. Automated negotiation allows two devices to negotiate data mode or rates. The above approach is specifically designed to enable incompatible devices to connect. For example, a device with a maximum data rate of 10 Mbps can communicate with a device with a data rate of 100 Mbps (it can operate at a slower speed).

Topology

Fast Ethernet is designed to connect two or more stations. If there are only two stations, they can be connected point by point. Three or more stations should be combined in a star topology with a hub or switch in the center (Figure 5).

Figure 5

Encoding

Fast Ethernet operates on an encryption system called Manchester, which uses 200 Mbaud bandwidth. It makes the technology unsuitable for media such as tangled cable. For this reason, fast Ethernet designers were looking for an alternative coding/decoding scheme.

However, it turned out that no plan worked equally well for all three implementations. Therefore, three good coding schemes, 100Base-TX, 100Base-FX, and 100Base-T4, were proposed.

Gigabit Ethernet (1000 Mbps)

The need for faster data transfer led to the emergence of the Gigabit Ethernet standard (1000 Mbps). The goal of Gigabit Ethernet was to speed up data transfer up to 1 Gbps, keeping the address length, frame format, maximum, and minimum frame lengths constant. The bar is also compatible with the 802.3z standard.

 The most important goals of Gigabit Ethernet are:

In recent years, Ethernet has played an essential role in the infrastructure of metropolitan areas. The IEEE Committee registered 10 Gigabit Ethernet as standard 802.3ae. The design goals of 10 Gigabit Ethernet can summarize as upgrading the data transfer rate to 10 Gbps. The idea is to increase data transfer speed and distance covered.

Maintaining the same frame size and format and the possibility of connecting LAN, MAN, and WAN networks were other goals of this project. The standard defines two types of physical layers, LAN PHY and WAN PHY. The first standard (LAN PHY) supports shared local area networks, and the second describes a WAN with connected connections via SONET OC-192.

MAC sublayer

One of the primary considerations in the evolution of Ethernet was the preservation of the Mac sublayer. However, it was impossible to maintain this architecture to achieve data speeds of 1 Gbps. Gigabit Ethernet uses two semi-duplex and all-duplex techniques to transmit data. Almost all Gigabit Ethernet implementations follow the all-duplex approach, so the semi-duplex mode is not often used.

A central switch is connected to all computers or switches in full-duplex mode.

In this case, each switch has buffers that hold data until it is sent to each input port. Since the controller uses the frame’s destination address and does not send the rack outside the port connected to that particular destination, there is no collision.

In other words, the CSMA / CD access method is no longer used. Gigabit Ethernet can also use in semi-duplex mode, Although not common.

In this case, a switch can replace with a hub that acts as a standard cable. Therefore, there is a possibility of a collision. The semi-duplex approach uses the CSMA / CD access method.

Exit mobile version